Jet
Aircraft
Electric Ducted Fan Jets
Cat
No. 10A10-S
A-10 Warthog For use with 40mm to 55mm fan units
|
A-10
Warthog Kit features SPECIFICATIONS Wing Span - 3i in Fan units
|
K&A Models A-10 is designed for use with
40mm to 55mm fan units. The A-10 can be hand launched with sufficient power however for
reliable launches a bungee assist is suggested. Dr. Mad fan units both 40mm and 50mm produce plenty of power for the A-10. We recommend the 40mm over the 50mm as a 3s setup is more suited for the A-10 and at 400 watts you will have plenty of power to spare. The A-10 is very stable in flight and performs great aerobatic maneuvers. Requires a 3 channel radio with 2 to 3 mini servos depending on how you set up the ailerons and a mini receiver. |
Order # 10L39M
L-39 Hollow Molded For use with 70 to 75mm fan units
|
L-39 ALBATROS Fast build kit SPECIFICATIONS Wing Span - 33.5 in Motors brushless Fan units
Our L-39M is a completely hollow molded
fiberglass airframe that is pre-primered in the molds. (Gray)
|
K&A Models is happy to announce the release of their new fully hollow molded fiberglass L-39 fast build kit for EDF. The L-39 is designed for use with 70 to 75mm fan units. This plane will really stand out at your flying field because it is designed for use with retracts. The L-39 takes down the runway straight smooth and stable for its take off. In the air the L-39 is very stable, predictable and yes very fast and eager to perform aerobatic maneuvers. The L-39 slows down nicely for landing approaches due to our newly designed hollow molded fiberglass wing. The kit assembles very quickly due to all of the major components having been pre built for you. There is no building in this kit just simply assembly. The landing gear blocks are pre-installed in the wings for the retracts. For the front nose gear a simple pre-marked and cut to shape nose gear tray gets installed in the nose of the plane after installing your nose retract and servo for steering. This is truly a top of the line fast build kit. The L-39 can still be used as a bungee launch airframe and if you decide to install the retracts later the retract mounting blocks are already installed for you. The L-39 requires a 3 to 5 channel radio with 3 to 5 mini servos. |
"ALL MOLDED" F-100 90mm EDF Cat No. 10F100-M
This airframe is retract ready Above photo shows the kit components for the |
F-100 EDF Pre-primed two piece fiberglass
fuselage, center hatch & canopy hatch with panel lines
SPECIFICATIONS Wing Span - 41 in
Motor brushless ESC motor control 70-90 amp Control function options
|
K&A Models is happy to announce the release of their new all molded F-100 electric ducted fan jet for 90mm fans. The F-100 is a super stable airframe lending itself to almost any pilot. The use of retracts also makes the F-100 suitable for just about any of the model flying sites. Features offered are pre-installed retract mounting blocks, fully molded flying surfaces with live hinging and a fully panel lined airframe for great detail. The F-100 lends itself to a number of different power units on the market and fan units. As for performance the F-100 is fully aerobatic and at 7lbs all up weight running on an 8s battery pack with retracts it slows down extremely well on landing approaches without flap deployment. The kit assembles very fast due to most all of the parts being pre-built for you. The F-100 is an ideal plane for the intermediate and advanced pilots alike. Requires a 4 to 5 channel radio with 4-7 mini servos. |
ALL MOLDED MiG-15 EDF Cat No. 10LM15-M This airframe is retract ready Above photo shows the kit components for the
|
MIG-15 EDF Cat No. 10LM15-M Pre-primed fiberglass fuselage & hatch with panel lines SPECIFICATIONS Wing Span - 37.75 in Motor brushless ESC motor control 45-90 amp
|
K&A Models is happy to announce the release of their new all molded MiG-15 electric ducted fan jet. This Mig-15 has shown up on the front cover of S&E Modeler Magazine as the Stoli and was originally designed by Steve Toschi of Northern CA. This new generation MiG-15 airframe has been updated with new all molded wings and stabilizers and the fuselage comes apart at the rear for ease of installing your power unit. Other updates are the pre-installed mounting plates for use with the MAP micro retracts as well as a fully panel lined airframe. The MiG-15 lends itself to a number of different power units on the market. As for performance the MiG-15 is very stable in flight and performs nice clean aerobatic maneuvers. With the addition of the retractable landing gear the MiG-15 seems to be twice as fun to fly. The kit assembles very fast due to most all of the parts being pre-built for you. The MiG-15 is an ideal plane for the intermediate and advanced pilots alike. Requires a 3 to 4 channel radio with 3-4 mini servos and mini receiver. |
Cat. No 10A6
The A-6 is designed to use just one fan to keep the power unit cost
|
A-6
Intruder SPECIFICATIONS Wing Span - 44.75 in Motors brushless Fan units
|
||
K&A Models is happy to announce the release of their new A-6 Intruder kit for EDF. The A-6 is designed for use with the mini 480 or 609 fan unit. This plane will really stand out at your flying field. The A-6 launches off the rails straight and smooth with very stable flight characteristics. The kit assembles very quickly due to the fully molded fiberglass fuselage along with hollow molded fiberglass wings as well as pre-cut to shape balsa and plywood parts. This is truly one of a kind. The A-6 requires a 3 channel radio with 3 to 4 mini servos and mini receiver. |
Cat. No 10V1
|
V-1 SPECIFICATIONS Wing Span - 37 in Motors brushless Fan units
|
|||||
K&A Models is happy to announce the release of their new V-1 Buzz Bomb kit for EDF. The V-1 is designed for use with the mini 480 or 505 fan units. This is an ideal first EDF plane. The NACA airfoil used along with the constant cord wing configuration makes for a very stable and easy plane to fly. The tail pipe on the motor nacelle slips off for easy installation of your power unit along with a slip on nose making radio installation a breeze. The kit assembles very quickly due to the fully molded fiberglass fuselage and motor nacelle along with hollow molded fiberglass wings as well as pre-cut to shape balsa and plywood parts. This is truly an outstanding kit. The V-1 requires a 3 channel radio with 3 mini servos and mini receiver. |
Cat.No 10ARES-M This model is retract ready |
Rutan
ARES SPECIFICATIONS Wing Span - 46.5 in Motors brushless Cat. No 10ARES-M Pre-primed fiberglass fuselage
|
K&A Models is happy to announce the release of their new RUTAN ARES kit for EDF. The ARES is designed for use with the mini 480 fan. Ideally you want to fly an EDF jet at or above 400 watts for jet like performance. The canard configuration of the ARES makes for an extremely stable plane in flight and has no bad habits we can see thus far. The kit assembles very quickly due to the fully molded fiberglass parts and pre-sheeted wings and canard as well as pre-cut to shape wood parts. The kit even comes with a pre-installed main wing spar and hard points for the tail booms. This is truly an outstanding kit. The ARES requires a 3 to 4 channel radio with 2 metal geared mini servos and mini receiver. |
Cat. No 10F84-P
|
REPUBLIC
F-84F
SPECIFICATIONS Wing Span - 33 in Motors brushless
|
|
K&A Models is happy to announce the release of their new F-84F THUNDERSTREAK kit for EDF. The F-84 is designed for use with the mini 480 fan or HW 609 fan. Ideally you want to fly an EDF jet at or above 400 watts for jet like performance. This type of performance can be reached using just a Kontronics fun 480 motor with a mini 480 fan running on 10 cells. Up to around 700 watts of power can be used with the F-84. The F-84 is extremely stable in flight and has no bad habits we can see thus far. The kit assembles very quickly due to the fully molded fiberglass fuselage with vertical fin molded in place and pre-cut to shape parts. The F-84 kit can also be ordered with pre-sheeted wings reducing the building time yet further. The F-84 requires a 3 to 4 channel radio with 3 mini servos and mini receiver. |
Cat No. 10262-P |
Me-262 EDF Cat No. 10262-P SPECIFICATIONS Wing Span -44 in
Motor brushless
|
K&A Models is happy to announce our new Me-262 EDF jet. The Me-262 is a outstanding performing EDF jet. Flown on the 65mm Vasa or Wattage fans using just a speed 400 motors on a 10 cell CP-1700 pack this little jet gets up an goes. The Me-262 is very stable in flight and fly's aerobatic maneuvers with ease. The kit builds very fast due to the fully molded fiberglass fuselage with the vertical fin molded in place as well as molded nacelles. The wings are foam cores that you sheet with 1/16" balsa sheeting provided. Requires a 3 to 4 channel radio with 3 mini servos and mini receiver. |
Cat No. 10F86-P Updates on the Park Jets in use with the WeMoTec
505 fan
|
F-86
Sabre Wing Span - 31 in Motor brushless
|
K&A has broke the barrier on park size EDF jets. K&A Models is happy to announce our F-86 Sabre EDF jet. The F-86 is a outstanding performing park size EDF jet. Flown on the 65mm fan on a 3 cell 2100 pack this little jet gets up an goes. The F-86 is very stable in flight, can be hand launched and fly's aerobatic maneuvers with ease. Requires a 3 to 4 channel radio with 3 mini servos and mini receiver. |
Cat No. 10LM15-P
Above photo. Kit parts of our 10LM15-P kit. |
MIG-15 EDF Cat No. 10LM15-P Pre-primed fiberglass fuselage &
hatch SPECIFICATIONS Wing Span - 37.75 in Motor brushless ESC motor control 40-90 amp |
K&A Models MiG-15 electric ducted fan jet. This Mig-15 has shown up on the front cover of S&E Modeler Magazine as the Stoli and was originally designed by Steve Toschi of Northern CA. The MiG-15 lends itself to a number of different power units on the market. The MiG-15 is very stable in flight and performs aerobatic maneuvers with ease. The kit builds very fast due to the fully molded fiberglass fuselage with molded inlet and exhaust liners, pre-cut to shape tail surfaces and pre-sheeted foam core wings. The MiG-15 is an ideal plane for the intermediate and advanced pilots alike. Requires a 3 to 4 channel radio with 3 mini servos and mini receiver. |
Cat No. 10SMIG-P
|
MIG-15
SPECIFICATIONS Wing Span - 31 in Motor brushed Motor brushless
|
K&A Models is happy to announce the upcoming release of their new MIG-15 EDF. Well we didn't feel it would be much fun just flying around an F-86 with nothing to chase so we did the right thing and made a MiG-15 to match. Just like the F-86 the MiG-15 is a great performer in the air. Stable in flight, easy to hand launch and performs great aerobatic maneuvers. So now you and a friend can see just who is the best pilot. Requires a 3 to 4 channel radio with 3 mini servos and mini receiver. |
Prop Jets
Cat No. 10F9F-P F9F PANTHER |
F9F PANTHER SPEED 400 Cat No. 10F9F-P SPECIFICATIONS Wing Span - 26.5 in Motor brushed Motor brushless
|
K&A's F9F PANTHER for direct drive speed 400 size motors. This is a new breed for the speed 400 class. The PANTHER comes with an epoxy fiberglass fuselage that has the inboard section of the wings and the vertical fin molded in place. The tail surfaces come to you pre-cut to shape. We have also added vacuum formed accessories such as tip tanks, canopy hatch with and clear canopy, battery tray and even a set of vacuum formed inlets to complete that scale look. The best thing is how well the PANTHER flys. The PANTHER is very stable in flight and performs great aerobatic maneuvers. The small size of the PANTHER makes it a great school yard flier. Pick up your PANTHER today and have one of the best looking prop jets around. Requires a 3 to 4 channel radio with 3 mini servos and mini receiver. |